Warning: preg_replace(): The /e modifier is deprecated, use preg_replace_callback instead in ..../includes/class_bbcode.php on line 2958
Dan Echo help
Results 1 to 8 of 8

Thread: Dan Echo help

  1. #1
    Join Date
    May 2009
    Posts
    391
    Post Thanks / Like

    Default Dan Echo help

    So I have a Dan Echo pedal. Looks like it spent time in the South Pacific during WWll. After using lots of DeOxit, it works with both 9v battery or wall wart, but it doesn't do anything. I mean it doesn't change the signal at all, doesn't change the volume. Just lights up and looks pretty.

    Any suggestions from some of you guru's? I don't mind pulling it apart or heating up a soldering iron, as it's only useful as a doorstop at this point. Thanks!
    "Always go heavy on the effects and try to blind the audience with expensive gear." - hubberjub

    I mean, no offense, but I don't really see why, like guitar players from Creed, or something like that, are on the cover of guitar magazines. Almost anybody can sit down and learn to play those songs.
    Dweezil Zappa

  2. #2
    Join Date
    Dec 2005
    Location
    Idaho (I-duh-ho)
    Posts
    12,581
    Post Thanks / Like

    Default

    It's probably fixable if you get power, but finding out what it is is going to take some sleuthing. If you pull out the circuit board do you notice any obviously burnt components?

    "No Tele For you." - The Tele Nazi

    Ha! Tele-ish now inbound.

  3. #3
    Join Date
    Jun 2008
    Location
    Down Under
    Posts
    1,706
    Post Thanks / Like

    Default

    I'm afraid I'm unfamiliar with the pedal, so without having it in front of me with a multi-meter in my hand I dunno.......

    Not to shoot Spud down, but depending on how the bypass is wired, an LED lighting might not mean anything at all. In a true bypass switching setup, the LED is on a completely independent circuit. You could literally remove all the bits that make the effect work and the led would still shine proudly....

    Spud is spot on with the visual inspection part though. Have a look for corrosion, liquid damage, cracks, burnt out bits, wires that don't go anywhere (because the have broken off) Given that it was used in the defense of Iwo Jima, all these are possible

  4. #4
    Join Date
    May 2009
    Posts
    391
    Post Thanks / Like

    Default

    OK. I'll pull it apart today and let you know what I find. Thanks!!
    "Always go heavy on the effects and try to blind the audience with expensive gear." - hubberjub

    I mean, no offense, but I don't really see why, like guitar players from Creed, or something like that, are on the cover of guitar magazines. Almost anybody can sit down and learn to play those songs.
    Dweezil Zappa

  5. #5
    Join Date
    May 2009
    Posts
    391
    Post Thanks / Like

    Default

    OK, here's some gut shots:





    You can see in the 2nd pic, the PCB looks pretty gonzo (in my unprofessional opinion). That's the smaller 'daughterboard' card plugged into the bigger board, and the one that the juice flows through. Giant doorstop, or can I fix it? Opinions??
    "Always go heavy on the effects and try to blind the audience with expensive gear." - hubberjub

    I mean, no offense, but I don't really see why, like guitar players from Creed, or something like that, are on the cover of guitar magazines. Almost anybody can sit down and learn to play those songs.
    Dweezil Zappa

  6. #6
    Join Date
    Jun 2008
    Location
    Down Under
    Posts
    1,706
    Post Thanks / Like

    Default

    Jeez man. If I was still in the repair game professionally I'd tag that B.E.R. immediately. "Beyond Economical Repair"

    Seriously, there is a lot of corrosion going on, meaning you would have to remove every single component from the PCB, strip it back to the copper traces and then go at it with a razor blade to cut out the corroded traces and replace with wire, drill out and through PCB connectors and replace with wire, re-coat the board in lacquer and hope you found all the corroded parts. Then replace every electro cap, all pots, sockets and connectors. Probably a good idea to replace all the resistors too, either replace the IC's or sand down the legs, and on it goes...

    If this was the last of it's kind and the future of mankind depended on it, Yeah I reckon I could make it work. Otherwise, throw it back in the creek it came from

  7. #7
    Join Date
    Nov 2009
    Location
    Kent, Ohio
    Posts
    1,271
    Post Thanks / Like
    Blog Entries
    2

    Default

    I have one of those pedals and it sounds like *** anyways. I say chuck it. I haven't found a Danelectro pedal that I like yet. Tried Rocky Road, Fish N Chips Reverb, Cool Cat Tremolo, and Danecho.

  8. #8
    Join Date
    Dec 2005
    Location
    Idaho (I-duh-ho)
    Posts
    12,581
    Post Thanks / Like

    Default

    Quote Originally Posted by Commodore 64 View Post
    I have one of those pedals and it sounds like *** anyways. I say chuck it. I haven't found a Danelectro pedal that I like yet. Tried Rocky Road, Fish N Chips Reverb, Cool Cat Tremolo, and Danecho.
    Well, you're missing the Chicken Salad. Great pedal fo sho.

    But ya, the Echo might be more headache than you need to get it working. However, you can turn it into a great classroom experience and see if eventually you can get it working, but I wouldn't invest any money in it, just time.

    "No Tele For you." - The Tele Nazi

    Ha! Tele-ish now inbound.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •