Dummy load for guitar amp

[Justaguyin_nc]

The real question is: how much are you willing to pay for something that has only like $5-$10 worth of parts? Especially, something as easy to make as this. (Disclaimer: this is not a commercial come on, just an explanation of the costs involved.)

tung

Welcome to thefret.net tung...

Welp, As far as how much.. that depends.. I thought this is the American way.. put a few bucks in a product and charge for it.. You also have to make an enclosure.. and have a female or male plug depending on design.. you have to buy in quanity if you really want anything cheap.. you have to add in shipping..and then there is the "labor time" making it...

I been searching for a dummy..ummm.. and find that I am not the only one.. many sites just say as you did..make one.. but that leads me to believe there are many people out there looking for one already made.. I personally feel its worth someplace between $15.00-$20.00 made.. ready to use.. and if its that cheap to make.. why isn't someone doing this?

I went to mouser..looked up 16 ohm 25 watt resistor just for the heck of it.. it came back with like 1000 different ones.. which at that point I was lost.. sigh... I probably will have to break down and make one from designs found on the net.. just suprised they are not already available.. there is a thing on e-bay..more of a attunator type, its around 50 bucks.. I might actually buy it before building my own.. just out of lazyness.. again an American way..

[tunghaichuan***]

Thanks for the welcome. I should introduce myself in the new members forum :


This is the part I would use:

http://www.mouser.com/search/Product...280-CR25-16-RC

For 8 ohm/100w:

http://www.mouser.com/search/Product...280-CR25-33-RC

Like with most of the parts at Mouser, the more you order, the cheaper the individual parts cost. The downside is that if you only need 4 of these resistors, and the plug, you're still going to be charged a minimum of $6 in the US for shipping. So this increases the DIY costs.

And you're right, I didn't even factor in the cost of the plug, or the wire either. I'd probably use some 3/8" long hex standoffs to insulate the board from the chassis. Doesn't seem so simple to me anymore

Here is a 4.7 ohm, 100w resistor for $12.00:

http://www.mouser.com/search/Product...284-HS100-4.7F

That way you can do away with the board and just attach a plug. Be careful, though, that resistor will get hot with a cranked amp putting power into it.

tung

Welcome to thefret.net tung...

Welp, As far as how much.. that depends.. I thought this is the American way.. put a few bucks in a product and charge for it.. You also have to make an enclosure.. and have a female or male plug depending on design.. you have to buy in quanity if you really want anything cheap.. you have to add in shipping..and then there is the "labor time" making it...

I been searching for a dummy..ummm.. and find that I am not the only one.. many sites just say as you did..make one.. but that leads me to believe there are many people out there looking for one already made.. I personally feel its worth someplace between $15.00-$20.00 made.. ready to use.. and if its that cheap to make.. why isn't someone doing this?

I went to mouser..looked up 16 ohm 25 watt resistor just for the heck of it.. it came back with like 1000 different ones.. which at that point I was lost.. sigh... I probably will have to break down and make one from designs found on the net.. just suprised they are not already available.. there is a thing on e-bay..more of a attunator type, its around 50 bucks.. I might actually buy it before building my own.. just out of lazyness.. again an American way..